Terex: equipment recalls

1. 26E016000Received 30 Mar 2026. 3,015 units.

   Equipment

   Defect, in the NHTSA record

   Terex South Dakota, Inc. (Terex) is recalling certain pole position guide arm assembly pins with part number 450543. An insufficient weld on the plate weldment may crack, causing the retaining pin to separate.

   Consequence, in the NHTSA record

   Without a retaining pin, the pole guide arm may fall, increasing the risk of injury to people around the truck.

   Remedy, in the NHTSA record

   Owners will inspect the plate weldment for any cracks or abnormal welds. Dealers or owners will replace the plate weldment as necessary, free of charge. Owner notification letters were mailed June 2, 2026. Owners may contact Terex's customer service at 1-605-882-4000. Terex's number for this recall is SN737E.

   Products named: Terex Pole Position Guide Arm Assembly Pin.

   Report filed by Terex South Dakota, Inc.. Manufacturer campaign number SN737E. Owner notification date in the NHTSA record: 2 Jun 2026.

2. 09E019000Received 27 Apr 2009. 23 units.

   Equipment

   Defect, in the NHTSA record

   Terex telelect, INC. Certain tlm series aerial devices which used mounting plate 471499 installed on utility trucks from december 2002 through november 2007. The plate can develop a crack at the base of the pedestal to the truck frame.

   Consequence, in the NHTSA record

   If the mounting plate fails, the boom and platform may fall, possibly resulting in serious injury or death.

   Remedy, in the NHTSA record

   Terex will notify owners and will reinforce the mounting plates free of charge. The recall is expected to begin during may 2009. Owners may contact terex utilities warranty by calling 1-605-884-3892.

   Products named: Terex TLM.

   Report filed by TEREX TELELECT, INC.. Manufacturer campaign number CB585. Owner notification date in the NHTSA record: 22 Jun 2009.

3. 08E068000Received 2 Dec 2008. 60 units.

   Equipment / Mechanical / Winch

   Defect, in the NHTSA record

   Terex telelect is recalling 60 30,000 lb bumper winches installed by terex telelect from january 2003 through october 2008 in certain utility trucks. The winches were installed to facilitate working on electrical services and communication lines both on and off road. These winches may be equipped with wire ropes that can not withstand the pull force of the bumper winch.

   Consequence, in the NHTSA record

   Pulling at full force on the bare winch drum may result in failure of the winch line and could result in death or serious injury.

   Remedy, in the NHTSA record

   Terex telelect will notify owners and replace the wire winch rope if it is less than 5/8" diameter free of charge. The recall began on december 22, 2008. Owners may contact terex utilities warranty department by calling 1-605-882-4000.

   Products named: Terex Bumper Winch.

   Report filed by TEREX TELELECT, INC.. Manufacturer campaign number CB583. Owner notification date in the NHTSA record: 22 Dec 2008.

4. 08E058000Received 12 Sep 2008. 142 units.

   Equipment

   Defect, in the NHTSA record

   Terex telelect is recalling 142 tlm series aerial devices built from january 2000 through march 2003. The pin retaining bolts that holds pivot pins or cylinder attaching pins in place can break due to lack of lubrication of the pin.

   Consequence, in the NHTSA record

   Failure of the retainer bolts allows the pin to move out of position and the boom to fall, possibly resulting in personal injury.

   Remedy, in the NHTSA record

   Terex will notify owners and replace the pin retainer fasteners free of charge. The recall began on september 26, 2008. Owners may contact terex utilities warranty department by calling 1-605-882-4000.

   Products named: Terex TLM.

   Report filed by TEREX TELELECT, INC.. Manufacturer campaign number CB582. Owner notification date in the NHTSA record: 26 Sep 2008.

5. 08E043000Received 1 Jul 2008. 60 units.

   Equipment

   Defect, in the NHTSA record

   Terex telelect is recalling 60 tcp40 series aerial devices built in 2007. The bolts that attach the boom tip bracket to the third boom can loosen and break.

   Consequence, in the NHTSA record

   If the failed fasteners are not repaired other components will eventually be damaged and may allow the platform to rotate, possibly resulting in personal injury.

   Remedy, in the NHTSA record

   Terex will notify owners and provide a remedy free of charge. The recall began on july 16, 2008. Owners may contact terex utilities warranty department by calling 1-605-882-4000.

   Products named: Terex TCP40.

   Report filed by TEREX TELELECT, INC.. Manufacturer campaign number CB581. Owner notification date in the NHTSA record: 16 Jul 2008.

6. 08E009000Received 25 Jan 2008. 1,167 units.

   Equipment

   Defect, in the NHTSA record

   Terex is recalling 1,167 tc series aerial devices equipped with check valve, p/n 443847, installed from september 2001 until march 2007. The valve is located on the lower boom lift cylinder. Failure can occur only when the vehicle is parked and the aerial device is in operation. The check valve is used in retiming of the boom when the platform is out of level. The flow through the check valve can cause the snap ring to fail if the retiming flow is abnormally high. The check valve components will flow into the lift cylinder if the snap ring fails.

   Consequence, in the NHTSA record

   Debris may scratch the cylinder wall or get into holding valves and cause the platform to drift down slowly, which could possibly result in serious injury or death to the platform user.

   Remedy, in the NHTSA record

   Terex will notify owners and replace the defective check valves free of charge. The recall began on february 7, 2008. Owners may contact terex utilities warranty department by calling 1-605-882-4000.

   Products named: Terex TC.

   Report filed by TEREX TELELECT, INC.. Manufacturer campaign number CB579. Owner notification date in the NHTSA record: 7 Feb 2008.

7. 08E008000Received 25 Jan 2008. 4,060 units.

   Equipment

   Defect, in the NHTSA record

   Terex is recalling 4,060 tc, tcx, xm, rm, rmx, om, tm, ha, 6-series, and fc series aerial devices equipped with hydraulic rotary selector valves, p/nos 68698, 459713, 463130, 476618, and 9118243, manufactured between january 1996 and january 1, 2008. The valve is used on closed center, hydraulic system, aerial devices. Failure can occur when the vehicle is parked and the aerial device is operating. The aerial devices are installed on trucks to transport the aerial device to the work site to facilitate working on electrical power lines and communication lines.

   Consequence, in the NHTSA record

   Failure of the valve may cause loss of oil, the handle being expelled at high speed, and the machine will be inoperable, which may result in serious injury or death to the operator.

   Remedy, in the NHTSA record

   Terex will notify owners and replace the defective hydraulic rotary select valve free of charge. The recall began on february 7, 2008. Owners may contact terex utilities warranty department by calling 1-605-882-4000.

   Products named: Terex TM; Terex OM; Terex HA; Terex TCX; Terex FC; Terex TC; Terex XM; Terex RMX; Terex 6 Series; Terex RM.

   Report filed by TEREX TELELECT, INC.. Manufacturer campaign number CB578. Owner notification date in the NHTSA record: 7 Feb 2008.

8. 07E068000Received 3 Sep 2007. 172 units.

   Equipment

   Defect, in the NHTSA record

   Certain terex aerial devices, models hr37/40, hrm and hrx equipped with basket lifter option using basket shaft weldmat 465451 manufactured between april 15, 2003, and july 24, 2007, can develope cracks near the weld in the support tube to the main upright tube.

   Consequence, in the NHTSA record

   Continued operation will allow the material to fatigue and fail resulting in uncontrolled platform movement and possible ejection of occupants. Serious injury or death could occur.

   Remedy, in the NHTSA record

   Terex will notify owners and repair the units free of charge. The recall began on september 20, 2007. Owners may contact terex at 1-605-882-4000.

   Products named: Terex HRM; Terex HR40; Terex HR37; Terex HRX.

   Report filed by TEREX TELELECT, INC.. Manufacturer campaign number CB575. Owner notification date in the NHTSA record: 20 Sep 2007.

9. 07E028000Received 27 Apr 2007. 446 units.

   Equipment

   Defect, in the NHTSA record

   Certain terex aerial devices p/no. Tc manufactured between july 16, 1996, and february 1, 2004, installed on trucks to transport the aerial device to the work site. Tc model aerial units, with the end mount platform, have a leveling sprocket at the lower boom that can develop cracks in the arm which controls platform position. Where the leveling cylinder attaches to the arm, it can crack near the counter sunk grease fitting and over time fatigue and fail.

   Consequence, in the NHTSA record

   If the arm fails, the platform movement is not controlled and may dump the platform occupants.

   Remedy, in the NHTSA record

   Terex telelect will notify owners and repair the aerial units free of charge. The recall began on june 1, 2007. Owners can contact terex at 1-605-882-4000.

   Products named: Terex TC.

   Report filed by TEREX TELELECT, INC.. Manufacturer campaign number CB 573. Owner notification date in the NHTSA record: 1 Jun 2007.

10. 07E001000Received 4 Jan 2007. 2,099 units.

    Equipment

    Defect, in the NHTSA record

    Certain terex telelect digger derricks and aerial devices equipped with check valves with p/nos engraved on the valve of; 1904f, 1908f, 1910f, and 1910r. These valves can fail which can cause the parts to move through the hydraulic system or will allow a vacuum to form in hydraulic lines if the pump flow should stop. These devices are installed on trucks to transport the aerial device or digger derrick to the work site to facilitate working on electrical power lines and communication lines or to trim trees.

    Consequence, in the NHTSA record

    Failure of the check valve can result in unexpected boom platform movement after the control lever is returned to the neutral position, or allow vacuum to form in hydraulic lines to the boom tip and could cause potential dielectric failure, possibly resulting in death or serious injury.

    Remedy, in the NHTSA record

    Terex utilities will notify owners and replace the check valves free of charge. The recall began on march 22, 2007. Owners may contact terex utilities service department at 1-605-882-4000.

    Products named: Terex XML; Terex C4000; Terex TCX; Terex OM; Terex FC; Terex C5000; Terex XT; Terex XM; Terex TC; Terex HRM; Terex General; Terex C6000, and 1 more.

    Report filed by TEREX TELELECT, INC.. Manufacturer campaign number CB 572. Owner notification date in the NHTSA record: 22 Mar 2007.

11. 06E070000Received 7 Aug 2006. 118 units.

    Equipment

    Defect, in the NHTSA record

    Certain terex aerial devices, tlp, tlm, and hr units, equipped with holding valves with caca and cwck model desigination produced with february 1 to april 10, 2006 date codes. A seal in the holding valve can fail and leak.

    Consequence, in the NHTSA record

    If seal leakage occurs, the boom may drift. A drifting platform can result in serious injury or death.

    Remedy, in the NHTSA record

    Terex will notify owners and replace the defective holding valves free of charge. The recall began on august 31, 2006. Owners may contact terex at 605-882-4000.

    Products named: Terex HR; Terex TLP; Terex TLM.

    Report filed by TEREX TELELECT, INC.. Manufacturer campaign number CB570. Owner notification date in the NHTSA record: 31 Aug 2006.

12. 06E053000Received 19 Jun 2006. 81 units.

    Equipment

    Defect, in the NHTSA record

    Certain terex aerial devices, models hr37 and hr40, which the upper boom cylinder (437249) and the lower boom cylinder (437250) may have a piston nut that is defective. These devices are installed on trucks to transport the aerial device to the work site.

    Consequence, in the NHTSA record

    Failure of this nut may cause the booms and platform to fall. A falling platform can result in death or serious injury.

    Remedy, in the NHTSA record

    Terex will notify owners and repair the units free of charge. The recall began on july 7, 2006. Owners may contact terex at 1-605-882-4000.

    Products named: Terex HR40; Terex HR37.

    Report filed by TEREX TELELECT, INC.. Manufacturer campaign number CB569. Owner notification date in the NHTSA record: 7 Jul 2006.

13. 06E045000Received 23 May 2006. 138 units.

    Equipment

    Defect, in the NHTSA record

    Certain terex aerial devices p/nos. Hr37 and hr40 installed on trucks to transport the aerial device to the work site. These units have a pivot plate at turntable that may fail during use.

    Consequence, in the NHTSA record

    Failure of this pivot plate may cause the platform to upset during use and cause the occupant to be ejected. This can cause death or serious injury.

    Remedy, in the NHTSA record

    Terex will notify owners and replace the units free of charge. The recall began on may 18, 2006. Owners may contact terex at 1-605-882-4000.

    Products named: Terex HR40; Terex HR37.

    Report filed by TEREX TELELECT, INC.. Manufacturer campaign number CB568.

14. 04E072000Received 17 Sep 2004. 47 units.

    Equipment

    Defect, in the NHTSA record

    Certain terex aerial devices p/n hr37 and hr40 installed on trucks to transport the aerial device to the work site. These units have a leveling sprocket weldment at the elbow end that may contain defective welds.

    Consequence, in the NHTSA record

    Failure of the weld may cause the platform to upset during use and cause the occupant to be ejected. This can cause death or serious injury.

    Remedy, in the NHTSA record

    The recall began during september 2004. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact terex utilities service department at 1-605-882-4000.

    Products named: Terex HR40; Terex HR37.

    Report filed by TEREX-TELELECT, INC.. Owner notification date in the NHTSA record: 18 Sep 2004.

The campaign number opens the NHTSA record.

Recall campaign: One recall in the NHTSA recall file, with one campaign number. A campaign can name many makes, models and model years.

Units: The number of vehicles or products that a recall can include. The manufacturer or the firm reports the number to the agency.

• HR374
• HR404
• TC4
• TLM3
• 6 Series2
• FC2
• HRM2
• OM2
• TCX2
• XM2
• Bumper Winch1
• C40001
• C50001
• C60001
• General1
• HA1
• HR1
• HRX1
• Pole Position Guide Arm Assembly Pin1
• RM1
• RMX1
• TCP401
• TLP1
• TM1
• XML1
• XT1

• All other equipment brands
• Terex: vehicle recalls
• Syntec5
• Takata27
• Tap2
• Tekonsha5
• Tenneco2
• Terran Industries2
• Tesla2
• Thermo King13
• Thule8
• Tiffin2

Follow by RSS:Child seat, tire and equipment recalls

• NHTSA recall lookupNHTSA shows the recalls of a child seat, a tire or equipment by brand and model.
• NHTSA: report a safety problemThe NHTSA form for a complaint about a vehicle, a tire, a child seat or equipment.

Which Terex products do the campaigns name?

The NHTSA records have 26 product names for these campaigns. The name in the most campaigns is: HR37

How many units does a Terex equipment campaign have?

The median Terex campaign has 142 units. The median of all 2,866 equipment campaigns is 1,677 units.

Which component do the Terex campaigns name most often?

Equipment, in 14 campaigns. The component is the first component in the NHTSA record of a campaign.